Duralast 700 Peak Amps Jump Starter Manual

The Duralast 700 Peak Amps Jump Starter is a portable power source designed for jump-starting vehicles with 12V batteries. It features a 700 peak amp output, built-in safety protections (reverse polarity, short circuit, over-current), a high-intensity LED work light, USB charging port for mobile devices, and a digital display showing battery status. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Instructions 3. Initial Setup & Charging 4. Specifications 5. Controls and Indicators 6. Jump-Starting Procedure 7. Using the USB Port & LED Light 8. Maintenance & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Jump starter unit, Heavy-duty clamps (red positive, black negative), DC charging adapter, USB cable, User manual.

Feature	Description
Peak Amps	700 amps for starting most gasoline engines up to 6.0L
Battery Type	Sealed lead-acid (SLA) rechargeable battery
Safety Protections	Reverse polarity, short circuit, over-current, over-charge
LED Work Light	High-intensity light with SOS flash mode
USB Charging Port	5V/2.1A output for smartphones/tablets
Digital Display	Shows internal battery charge level (percentage)
Clamp Cables	Insulated 40-inch cables with spark-proof design
Charging Input	12V DC adapter for wall outlet charging
Weight	Approximately 15 lbs (6.8 kg)
Operating Temp	14°F to 122°F (-10°C to 50°C)

Safety Instructions

Read all instructions before use. Failure to follow may cause injury or damage.

Explosion Risk: Do not use near flammable materials or open flame.
Electrical Shock: Keep unit dry; do not expose to rain or moisture.
Battery Acid: If battery leaks, avoid contact; use gloves and dispose properly.
Children: Keep out of reach of children.
Clamp Connection: Connect red to positive (+), black to negative (-) or grounded metal. Ensure clamps do not touch each other.
Vehicle Battery: Check for damage/cracks before connecting.

WARNING! Never attempt to jump-start frozen batteries. Do not use for engines over 6.0L diesel or 8-cylinder gasoline.

Initial Setup & Charging

Before first use, fully charge the jump starter.

Connect the DC charging adapter to the unit's charging port.
Plug adapter into a standard 120V AC wall outlet.
The digital display will show charging progress. Full charge indicated by 100%.
Initial charge may take up to 12 hours. Recharge after each use.

CAUTION! Charge only with provided adapter in a well-ventilated area. Do not leave charging unattended for extended periods.

Specifications

Model: Duralast 700 Peak Amps Jump Starter
Peak Current: 700 Amps
Cranking Current: 350 Amps
Battery Voltage: 12V DC
Internal Battery: 18Ah sealed lead-acid
USB Output: 5V DC, 2.1A max
Charging Input: 12V DC, 1A
LED Light: 120 lumens, 3 modes (steady, flash, SOS)
Clamp Cable Length: 40 inches (101.6 cm)
Dimensions: 11.8" x 7.5" x 3.2" (30 x 19 x 8 cm)
Weight: 15 lbs (6.8 kg)
Compliance: FCC Part 15 Class B, RoHS

Controls and Indicators

Front Panel: POWER button, USB port, LED light button, Digital display, Charging port.

Digital Display: Shows battery percentage (0-100%). Flashing if below 20%.

LED Light: Press once for steady light, twice for flashing, three times for SOS mode, fourth press turns off.

Power Button: Press to turn on jump starter readiness (clamps active). Unit will auto-shutoff after 30 seconds if no connection detected.

Status Indicators: Green LED = fully charged; Red LED = charging/low battery.

Jump-Starting Procedure

Follow steps in order. Ensure vehicle is in Park (automatic) or Neutral (manual) with ignition OFF.

Check jump starter battery level (display should show at least 50%).
Press POWER button to activate jump starter.
Connect red clamp to positive (+) terminal of dead vehicle battery.
Connect black clamp to negative (-) terminal or unpainted metal engine block.
Start the vehicle (crank for no more than 3 seconds).
Once vehicle starts, remove black clamp first, then red clamp.
Press POWER button to turn off jump starter.
Recharge jump starter as soon as possible.

Tip: If vehicle doesn't start after 3 attempts, wait 3 minutes between attempts to cool unit.

Using the USB Port & LED Light

USB Charging: Connect USB cable to port and device. The jump starter must be turned ON (POWER button). Do not charge devices while jump-starting.

LED Light: Useful for emergency lighting or roadside repairs. SOS mode alerts for help.

Note: Using USB or LED light reduces jump starter battery. Recharge after extended use.

Maintenance & Storage

Store in cool, dry place away from direct sunlight. Recharge every 3 months if not used. Clean clamps with dry cloth after use.

CAUTION! Do not disassemble unit. If damaged, discontinue use. For battery disposal, follow local regulations for lead-acid batteries.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Jump starter won't turn on	Battery depleted	Recharge fully (12+ hours). Check power outlet.
Vehicle doesn't start	Poor connection, low charge	Ensure clamps have solid contact. Recharge jump starter to >50%.
Digital display blank	Battery completely dead	Charge for 1 hour, then check display. If still blank, unit may need replacement.
USB port not working	Jump starter off/low battery	Press POWER button to turn on. Recharge if battery low.
LED light dim	Low battery	Recharge unit.
Clamps spark when connecting	Reverse polarity	Immediately disconnect. Verify red to positive, black to negative/ground.

Reset: Disconnect all cables, turn off, recharge fully.

Service: 1-800-XXX-XXXX; www.duralast.com