Everstart 1200 Peak Amp Jump Starter Manual

The Everstart 1200 Peak Amp Jump Starter is a portable power source designed to jump-start vehicles with 12V batteries. It features a high peak current of 1200 amps, built-in safety protections, a USB charging port for devices, an LED work light, and reverse polarity alarm. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Instructions 3. Components & Parts 4. Specifications 5. Initial Setup & Charging 6. Jump-Starting Procedure 7. Using the USB Port & LED Light 8. Maintenance & Storage 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-capacity sealed lead-acid battery, heavy-duty clamps, integrated charger, USB output port, LED work light, carrying case.

Feature	Description
Peak Current	1200 Amps for starting most gasoline engines
Battery Type	Sealed Lead-Acid (SLA), maintenance-free
USB Output	5V/2.1A port for charging phones, tablets
LED Work Light	Bright LED for emergency lighting
Safety Protection	Reverse polarity alarm, overload protection, spark-proof design
Charger Input	AC wall charger included (120V)
Clamps	Heavy-duty, copper-jawed with insulated handles
Carrying Case	Durable case for storage and transport
Battery Indicator	LED status lights for charge level
Weight	Approximately 18 lbs (8.2 kg)

Safety Instructions

Read all instructions before use to prevent injury or damage.

Wear safety glasses and gloves when jump-starting.
Ensure jump starter and vehicle are off before connecting clamps.
Connect positive (red) clamp to positive battery terminal first.
Connect negative (black) clamp to vehicle's engine block or grounded metal, NOT to battery negative.
Keep away from flames, sparks, and heat sources.
Do not use if unit is damaged, cracked, or leaking.

WARNING! Risk of explosion or acid burn. Follow polarity instructions carefully. Do not jump-start frozen batteries.

Components & Parts

Identify all parts before operation.

Main Unit: Contains battery, controls, and ports.
Jumper Cables: Heavy-gauge cables with clamps (red/black).
AC Charger: Plugs into wall outlet and unit's charging port.
USB Cable: For device charging (may be included).
LED Work Light: Button-controlled light on front.
Battery Indicator: Multi-LED display showing charge level.
Carrying Handle: For easy transport.

CAUTION! Inspect cables and clamps for damage before each use.

Specifications

Model: Everstart 1200 Peak Amp Jump Starter.
Peak Current: 1200 Amps.
Battery Voltage: 12V DC.
Battery Capacity: Typically 18Ah (sealed lead-acid).
USB Output: 5V DC, 2.1A max.
Charger Input: 120V AC, 60Hz.
LED Light: High-intensity white LED.
Operating Temp: -4°F to 140°F (-20°C to 60°C).
Storage Temp: 32°F to 77°F (0°C to 25°C) recommended.
Dimensions: Approx. 11" x 7" x 9".

Initial Setup & Charging

Charge fully before first use.

Plug AC charger into wall outlet (120V).
Connect charger plug to unit's charging port.
Charge until all LED indicator lights are solid (typically 12-24 hours).
Unplug charger after full charge.
Check battery indicator: Green lights indicate high charge; red indicates low.

Tip: Recharge every 3 months if not used to maintain battery health.

Jump-Starting Procedure

Follow steps in order for safe jump-start.

Ensure jump starter is off and vehicle ignition is off.
Connect red positive clamp to positive (+) terminal of vehicle battery.
Connect black negative clamp to clean, unpainted metal part of engine block or chassis.
Turn on jump starter (if equipped with power switch).
Start vehicle: Turn ignition; if engine doesn't start within 5 seconds, wait 3 minutes before retry.
After vehicle starts: Turn off jump starter.
Remove clamps in reverse order: Black negative first, then red positive.
Recharge jump starter after use.

WARNING! Do not touch clamps together when unit is on. Avoid contact between positive clamp and vehicle metal.

Using the USB Port & LED Light

Additional functions for convenience.

USB Charging: Connect USB cable from unit's port to device (phone, tablet). Unit must be charged and turned on (if applicable).
LED Work Light: Press and hold light button for steady beam; press quickly for flashing mode. Useful for emergencies or repairs.
Battery Indicator: Check LED lights to monitor remaining charge before use.

Note: Using USB or light will drain battery; recharge as needed.

Maintenance & Storage

Proper care extends product life.

Recharge fully every 3 months during storage.
Store in cool, dry place away from direct sunlight.
Keep clamps clean and free of corrosion.
Wipe exterior with dry cloth; do not use liquids.
Do not disassemble unit; no user-serviceable parts inside.

CAUTION! Do not expose to water or extreme temperatures. Dispose of battery according to local regulations.

Regulatory Information

FCC Part 15: Class B digital device; complies with limits for residential use. Copyright © Everstart; trademarks of respective owners. Contains sealed lead-acid battery; follow local disposal laws. For support, visit www.everstart.com or contact 1-800-XXX-XXXX.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Recharge fully (12-24 hours).
No power to vehicle	Poor connections	Ensure clamps have solid contact; clean terminals.
Reverse polarity alarm sounds	Clamps reversed	Immediately disconnect and reconnect with correct polarity.
Vehicle doesn't start	Engine too large/battery dead	Check vehicle battery condition; unit may be insufficient for large diesel engines.
USB port not working	Low battery/unit off	Recharge unit; ensure power is on.
LED light dim or off	Battery low	Recharge unit.

Reset: Disconnect all cables, recharge fully, and retry.

Service: 1-800-XXX-XXXX; www.everstart.com