Everstart 700 Amp Jump Starter Manual

The Everstart 700 Amp Jump Starter is a portable power source designed to jump-start 12V vehicles (cars, trucks, SUVs, motorcycles, boats) with gasoline engines up to 7.0 liters or diesel engines up to 4.5 liters. It features a 700-amp peak current, a built-in 120 PSI air compressor, a 3W LED work light with emergency flash mode, a USB charging port (5V/2.1A) for mobile devices, overload protection, reverse polarity protection, and a digital display showing battery status. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Jump starter main unit, Heavy-duty booster clamps (red/black), 12V DC charging adapter, Air hose with accessories, USB charging cable, User manual.

Safety Instructions

Read all instructions before use. Keep away from children.

1. Wear safety glasses and gloves when jump-starting.
2. Ensure jump starter and vehicle are off before connecting clamps.
3. Connect RED clamp to positive (+) terminal first, then BLACK to negative (-) or grounded metal.
4. Do not use with damaged cables or clamps. Do not submerge in water.
5. Keep away from heat, flames, and sparks. Do not disassemble.

WARNING! Risk of explosion. Do not jump-start frozen batteries. Ensure vehicle voltage is 12V DC only.

Components & Indicators

Front Panel: Power button, Digital display (battery %), LED light button, USB port, Compressor switch, Air hose connector. Side: DC input port, Storage for cables.

Indicator Lights: Digital display shows 100%-20% (green), 19%-10% (yellow), below 10% (red, recharge needed). LED light: Press once for steady light, twice for flashing, third time off.

Clamps: RED = Positive (+), BLACK = Negative (-). Ensure clamps are fully seated on terminals.

Specifications

• Peak Current: 700 Amps.
• Air Compressor: Max pressure 120 PSI, duty cycle 10 minutes on/20 minutes off.
• LED Light: 3W, 200 lumens, 120-degree beam angle.
• USB Output: 5V DC, 2.1A max.
• Internal Battery: Sealed lead-acid or lithium (model dependent), 12V.
• Charging Input: 12V DC, 1A.
• Operating Temp: -4°F to 140°F (-20°C to 60°C).
• Dimensions: Approximately 10" x 7" x 3".
• Weight: Approximately 8 lbs.

Charging the Unit

Charge fully before first use and after each use.

1. Plug the 12V DC adapter into the unit's DC input port.
2. Plug the adapter into a standard 120V AC wall outlet.
3. The digital display will show charging progress (flashing). When solid green (100%), charging is complete.
4. Disconnect adapter. A full charge may take 12-24 hours.

CAUTION! Charge in a well-ventilated area. Do not charge near flammable materials. Use only provided adapter.

Jump-Starting a Vehicle

For 12V negative-ground vehicles only.

1. Ensure jump starter is off. Turn off vehicle ignition and all accessories.
2. Connect RED clamp to positive (+) terminal of dead vehicle battery.
3. Connect BLACK clamp to a solid, unpainted metal part of engine block or chassis (ground), away from battery and fuel lines.
4. Turn jump starter power ON. Digital display will activate.
5. Start the vehicle. Once engine runs, turn jump starter OFF.
6. Remove clamps in reverse order: BLACK first, then RED.
7. Recharge jump starter as soon as possible.

Tip: If vehicle does not start within 5-6 seconds, wait 3 minutes before retrying. Do not crank for more than 6 seconds continuously.

Using the Air Compressor

For inflating tires, sports balls, air mattresses (use proper adapter).

1. Ensure compressor switch is OFF. Connect air hose to unit's connector.
2. Attach hose nozzle to tire valve or item to be inflated.
3. Turn compressor switch ON. Monitor pressure on built-in gauge.
4. When desired pressure is reached, turn switch OFF.
5. Disconnect hose. Do not exceed 120 PSI or recommended pressure for item.

WARNING! Compressor may get hot. Do not operate for more than 10 minutes continuously. Allow 20 minutes cool-down.

Using the LED Light & USB Port

LED Light: Press light button to cycle modes (Steady On -> Flashing -> Off). Ideal for roadside emergencies or work areas.

USB Port: Connect your device's USB cable to the port. The jump starter must be turned ON. The USB port will automatically supply power. Disconnect when charging is complete to conserve battery.

Note: Using LED light or USB port will drain the internal battery. Recharge as needed.

Care & Storage

Store in a cool, dry place. Recharge every 3 months if not in use to maintain battery health. Clean with a dry cloth. Do not use chemicals or water.

CAUTION! Do not store with clamps connected to each other or to the unit's terminals. Keep away from metal objects to prevent short circuits.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. This product contains chemicals known to cause cancer and birth defects (California Prop 65). Dispose of properly according to local regulations. Do not dispose of in household trash. For support, contact Walmart Auto Care Centers or visit www.everstart.com.

Troubleshooting

Reset: Turn unit off, disconnect all loads, wait 5 minutes, then turn on.

Service: For warranty or repair, contact 1-800-XXX-XXXX or www.everstart.com. Do not open the casing.