everstart 750 jump starter manual how to use

The EverStart 750 Jump Starter is a portable power source designed to jump-start vehicles with 12V batteries. It features a high-output 750-amp peak current, a built-in 120 PSI air compressor, a 3-in-1 USB charging port, a bright LED work light with emergency flash mode, and reverse polarity protection. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Jump starter unit with built-in battery, Heavy-duty clamps, Air compressor hose with accessories, USB charging cable, LED work light, AC wall charger.

Safety Precautions

Read all instructions before use. Keep away from children.

1. Wear safety glasses: Protect eyes from sparks or battery acid.
2. Check vehicle battery: Ensure it is a 12V lead-acid battery. Do not use on 24V systems.
3. Avoid flames/sparks: Keep away from open flame and do not smoke.
4. Ensure good ventilation: Use in a well-ventilated area.
5. Inspect cables/clamps: Do not use if damaged.

WARNING! Risk of explosion. Connect clamps correctly: RED to POSITIVE (+), BLACK to NEGATIVE (-) or unpainted metal ground. Never connect both clamps directly to battery terminals on a dead battery; connect negative to vehicle chassis.

Initial Setup & Charging

Before first use, fully charge the jump starter.

1. Plug AC charger into wall outlet and into the unit's charging port.
2. Charge until all battery indicator LEDs are solid (approx. 4-6 hours).
3. Unplug charger. The unit is now ready for use.
4. For long-term storage, recharge every 3 months.

CAUTION! Use only the provided charger. Charge in a dry, cool location away from direct sunlight.

Specifications

• Model: EverStart 750.
• Peak Amps: 750A.
• Air Compressor: 120 PSI maximum pressure.
• USB Output: 5V DC, 2.1A max.
• Internal Battery: Sealed lead-acid (SLA) or Lithium (model dependent).
• LED Light: White, with SOS flash mode.
• Clamp Cable Length: 20 inches.
• Operating Temp: -4°F to 140°F (-20°C to 60°C).
• Weight: Approximately 8 lbs.

Controls and Indicators

Front Panel: POWER button, Battery Status LEDs (4 levels), Compressor button, Light mode button, USB port.

LED Indicators: Green (75-100%), Yellow (50-75%), Orange (25-50%), Red (0-25%). A flashing red light indicates very low charge.

Light Modes: Press LIGHT button once for steady light, twice for SOS flash, three times for off. Compressor: Press COMPRESSOR button to turn on/off; built-in pressure gauge. Power Button: Turns main unit on/off for jump-start function.

Jump-Starting a Vehicle

Follow these steps carefully.

1. Ensure jump starter is OFF. Park vehicles safely, turn off ignition and all accessories.
2. Connect RED clamp to POSITIVE (+) terminal of dead vehicle battery.
3. Connect BLACK clamp to a clean, unpainted metal part of the engine block or chassis (ground), away from battery and fuel lines.
4. Turn jump starter ON (press POWER button).
5. Start the vehicle. Crank for no more than 3 seconds. Wait 30 seconds between attempts.
6. Once vehicle starts, turn jump starter OFF.
7. Remove clamps in REVERSE order: BLACK clamp first, then RED clamp.
8. Recharge jump starter as soon as possible after use.

Tip: If vehicle does not start after 3 attempts, there may be another problem. Do not continue cranking.

Using the Air Compressor

For inflating tires, sports balls, or air mattresses.

1. Ensure unit is charged and turned OFF.
2. Attach appropriate hose adapter to the compressor outlet.
3. Attach other end of hose to item being inflated.
4. Turn unit ON, then press COMPRESSOR button.
5. Monitor pressure using built-in gauge. Do not exceed recommended PSI.
6. Press COMPRESSOR button to stop. Turn unit OFF.
7. Allow compressor to cool for 10 minutes after continuous use of 10 minutes.

WARNING! Do not use compressor for more than 10 minutes continuously to prevent overheating.

Powering Devices & Using the Light

USB Port: Connect your device using a USB cable. The unit will supply power as long as the battery has charge. The battery indicator will show remaining capacity.

LED Light: Use for emergency lighting, roadside repairs, or camping. SOS mode is for emergencies to signal for help.

Care & Storage

Keep unit clean and dry. Wipe with a dry cloth. Store in the included case or a dry place at room temperature.

CAUTION! Do not expose to extreme heat or cold for prolonged periods. Do not disassemble. Recharge every 3 months if not in use.

Warranty Information

Limited warranty period: Check packaging or receipt for details. Warranty covers defects in materials and workmanship. Not covered: Damage from misuse, improper charging, or unauthorized repair. For warranty service, contact Walmart customer service or the manufacturer. Keep your receipt as proof of purchase.

Troubleshooting

Reset: If unit behaves erratically, turn off, disconnect all devices, and recharge fully.

Service: For issues not resolved above, contact Walmart Customer Service or refer to the warranty information.