Everstart 750 Peak Amps Jump Starter Manual

The Everstart 750 Peak Amps Jump Starter is a portable power source designed for jump-starting vehicles with 12V batteries. It features a high-output 750 peak amp battery, built-in safety protections, a USB charging port, an LED work light, and reverse polarity alarm. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Warnings 3. Initial Setup & Charging 4. Specifications 5. Controls and Indicators 6. Jump-Starting Procedure 7. Using the USB Port & Light 8. Maintenance & Storage 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-capacity sealed lead-acid battery, heavy-duty clamps, integrated USB port, LED work light, digital display (if equipped), and carrying case.

Feature	Description
Peak Amps	750 Amps for starting most gasoline engines
Battery Type	Sealed Lead-Acid (SLA), maintenance-free
Clamps	Heavy-duty, insulated with reverse polarity protection
USB Port	5V/2.1A output for charging phones/tablets
LED Work Light	High-intensity light with multiple modes (steady/flash)
Digital Display	Shows battery charge level (if model includes)
Safety Alarm	Audible alert for incorrect connection
Carrying Case	Protective storage with cable management
AC Charger	Included wall charger for recharging unit
Overload Protection	Protects against short circuit and overload

Safety Warnings

Read all instructions before use. Failure to follow may cause injury or damage.

Use only on 12V DC automotive batteries. Do not use on 6V or 24V systems.
Ensure jump starter and vehicle are off before connecting clamps.
Connect positive (+) to positive, negative (-) to unpainted metal ground.
Keep away from flames, sparks, and heat. Battery may emit explosive gases.
Do not disassemble or modify unit. Contact authorized service for repairs.

WARNING! Risk of explosion or acid burn. Do not expose to fire or high temperatures. Wear eye protection.

Initial Setup & Charging

Charge fully before first use and after each use for optimal performance.

Unpack and inspect for damage.
Plug AC charger into wall outlet and into jump starter's charging port.
Charge until indicator shows full (typically 8-12 hours for initial charge).
Disconnect charger once complete. Store in a cool, dry place.

CAUTION! Charge only with provided charger. Do not leave charging unattended for extended periods.

Specifications

Peak Current: 750 Amps.
Rated Voltage: 12V DC.
Battery Capacity: Typically 18Ah (may vary by model).
USB Output: 5V DC, 2.1A Max.
LED Light: High-power LED, multiple modes.
Charging Input: 120V AC, 60Hz (US).
Operating Temp: -4°F to 140°F (-20°C to 60°C).
Storage Temp: 32°F to 77°F (0°C to 25°C) recommended.
Weight: Approximately 15-18 lbs (varies by model).
Dimensions: Roughly 10" x 7" x 3" (varies).

Controls and Indicators

Front Panel: POWER button, USB port, LED light button, charge level indicators (LED bars or digital display). Clamps: Red (+) and Black (-), clearly marked.

Indicator Lights: Green = fully charged, Yellow = medium charge, Red = low charge, Flashing Red = needs recharge. Audible Alarm: Sounds if clamps are reversed. LED Light: Press once for steady, twice for flashing, hold to turn off.

Jump-Starting Procedure

Follow steps in order. Ensure vehicles are not touching.

Turn off jump starter and vehicle ignition.
Connect red clamp to positive (+) terminal of dead battery.
Connect black clamp to unpainted metal ground on engine block or chassis (away from battery).
Turn on jump starter (press POWER). Some models activate automatically upon correct connection.
Start vehicle. If it doesn't start within 5-6 seconds, wait 3 minutes before retrying.
Once vehicle starts, turn off jump starter.
Remove black clamp first, then red clamp.
Recharge jump starter as soon as possible.

Tip: If alarm sounds, check connections immediately. Do not force start if unit feels hot.

Using the USB Port & Light

USB: For charging portable devices only. Not for jump-starting.

Ensure jump starter is charged (green indicator).
Connect USB cable from device to jump starter's USB port.
Device should begin charging. Disconnect when done.
LED Light: Press button to cycle modes (On > Flash > Off). Useful for emergency lighting.

WARNING! Do not use USB port while jump-starting. Do not exceed 2.1A total draw.

Maintenance & Storage

Recharge every 3 months if not used. Keep clean and dry.

Wipe exterior with dry cloth. Do not use liquids.
Check clamps for corrosion; clean with wire brush if needed.
Store in included case, in a cool, dry location away from children.
Dispose of properly according to local regulations; do not incinerate.

CAUTION! Never store in discharged state. Avoid extreme temperatures.

Regulatory Information

FCC Part 15: Class B digital device; complies with limits for residential use. Copyright © Everstart; trademarks of respective owners. Contains sealed lead-acid battery; follow local disposal laws. For support, visit www.everstart.com or contact 1-800-XXX-XXXX.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Recharge fully (8-12 hours). Check charger connection.
Alarm sounds when connecting	Reverse polarity	Immediately disconnect and verify red to (+), black to ground.
Vehicle doesn't start	Insufficient charge, bad connections	Recharge unit. Ensure clamps have solid metal contact.
USB port not working	Low battery, faulty cable	Recharge jump starter. Try a different USB cable.
LED light dim or off	Battery low	Recharge unit. Press mode button firmly.
Unit gets hot during use	Overuse, short circuit	Allow to cool. Do not attempt more than 3 starts in a row.

Reset: Disconnect all cables, turn off, recharge fully.

Service: 1-800-XXX-XXXX; www.everstart.com