Everstart Jump Starter 1200 Manual

The Everstart Jump Starter 1200 is a portable power station and emergency jump starter designed for 12V vehicles. It features a high-capacity sealed lead-acid battery, 1200 peak amps, built-in air compressor, 12V DC power outlet, USB charging ports, LED work light, and reverse polarity protection. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Jump Starter Unit, Heavy-Duty Clamps, AC Wall Charger, 12V Vehicle Charger, Air Compressor Hose & Accessories, User Manual.

Safety Information

Read all instructions before use. This product contains a sealed lead-acid battery.

1. Explosion Hazard: Do not expose to fire or extreme heat. Do not charge near flammable materials.
2. Electrical Shock: Keep dry. Do not operate with wet hands or in rain.
3. Jump Starting: Connect clamps in correct order (positive first, then negative). Ensure vehicles do not touch.
4. Battery: Do not disassemble, crush, or puncture. Dispose of properly according to local regulations.
5. Children: Keep out of reach of children.

WARNING! Incorrect use can cause battery explosion, fire, or serious injury. Always wear safety glasses.

First-Time Setup & Charging

Fully charge the unit before first use and after each use for best performance.

1. AC Charging: Plug the AC wall charger into a standard 120V outlet, then connect to the unit's charging port. Charge for 12-24 hours initially.
2. DC Charging (Vehicle): Plug the 12V charger into your vehicle's cigarette lighter socket while the engine is running, then connect to the unit.
3. Charge Indicator: The LED battery gauge will illuminate segments as it charges. All segments lit indicates full charge.
4. Storage Charge: Recharge every 3 months if not in use to maintain battery health.

CAUTION! Charge in a well-ventilated area. Do not leave unattended while charging.

Specifications

• Model: Everstart Jump Starter 1200
• Peak Amps: 1200A
• Cranking Amps: 400A
• Battery Voltage: 12V DC
• Battery Capacity: 18Ah Sealed Lead-Acid
• Air Compressor: 120 PSI maximum, 35 L/min flow
• DC Output: 12V/10A (max)
• USB Output: 5V/2.1A
• LED Light: High-intensity white LED
• Charging Input: AC 120V 60Hz / DC 12V
• Operating Temp: 14°F to 122°F (-10°C to 50°C)
• Weight: Approx. 18 lbs (8.2 kg)

Controls and Indicators

Front Panel Layout: Battery Gauge (5 LED segments), Power Button, Air Compressor Button, LED Light Button, USB Ports, 12V DC Outlet, Charging Port.

Indicator Lights:

• Battery Gauge: Shows charge level (1 red = low, 5 green = full).
• Power/Status LED: Green = ready, Red = charging, Flashing Red = fault.
• Reverse Polarity Alarm: Loud beep and flashing red light if clamps are reversed.

Buttons:

• Power: Press to turn on DC outlet and USB ports.
• Air Compressor: Press to activate compressor; press again to turn off.
• LED Light: Press once for steady light, twice for flashing SOS, third time to turn off.

Jump Starting a Vehicle

Follow these steps carefully. Ensure the jump starter is fully charged.

1. Preparation: Turn off both vehicles and all accessories (radio, lights).
2. Connect Red Clamp (+): Attach to the positive (+) terminal of the dead vehicle's battery.
3. Connect Black Clamp (-): Attach to a clean, unpainted metal part of the engine block or chassis (ground), away from the battery.
4. Power On: Press the Power button on the jump starter. The status light should turn green.
5. Start Vehicle: Attempt to start the disabled vehicle. Crank for no more than 3-5 seconds. Wait 30 seconds between attempts.
6. Disconnect: Once started, immediately press Power button off. Remove BLACK clamp first, then RED clamp.

WARNING! Never connect clamps directly to each other. Do not touch clamps together during operation.

Using the Air Compressor

For inflating tires, sports balls, air mattresses, etc.

1. Ensure the unit is charged and turned OFF.
2. Screw the compressor hose onto the unit's air outlet valve tightly.
3. Attach the appropriate nozzle to the hose for your item (tire chuck, needle adapter, etc.).
4. Connect the nozzle to the item to be inflated.
5. Press the Air Compressor button to start. Monitor the built-in pressure gauge.
6. When desired pressure is reached, press the Air Compressor button again to stop.
7. Disconnect the nozzle, then unscrew the hose from the unit.

Tip: Do not run the compressor continuously for more than 10 minutes. Allow to cool between uses.

Using as a Power Source

The unit can power 12V DC accessories and charge USB devices.

1. For 12V Accessories: Plug the accessory (e.g., tire inflator, portable cooler) into the 12V DC outlet. Press the Power button to provide power.
2. For USB Devices: Connect your phone, tablet, or other USB device using a standard USB cable. No need to press Power button; USB ports are always live when unit has charge.
3. LED Work Light: Press the Light button to cycle through modes: On > Flashing SOS > Off.

Note: The 12V outlet will automatically shut off after 30 minutes of inactivity to conserve battery.

Maintenance & Storage

Proper care extends the life of your jump starter.

• Cleaning: Wipe exterior with a dry cloth. Do not use liquids or solvents.
• Battery Maintenance: Recharge fully every 3 months if not in regular use.
• Clamp Care: Keep clamps clean and free of corrosion. Wipe with a dry cloth after use.
• Storage: Store in a cool, dry place away from direct sunlight and extreme temperatures. Ideal storage temperature is 50°F to 77°F (10°C to 25°C).
• Transport: Use the carrying handle. Secure in vehicle to prevent tipping or damage.

CAUTION! Never store with the clamps connected to each other or to the unit's terminals.

Regulatory Information

FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Battery Disposal: Contains a sealed lead-acid battery. Must be disposed of according to local, state, and federal regulations. Do not dispose of in household trash. Warranty: Limited 1-year warranty from date of purchase. For warranty service, contact Everstart customer service with proof of purchase. Copyright © Everstart. For support, visit www.everstart.com or contact 1-800-XXX-XXXX.

Troubleshooting

Reset: If unit behaves erratically, disconnect all devices and clamps, then press and hold the Power button for 10 seconds.

Service: 1-800-XXX-XXXX; www.everstart.com