touring items type s jump starter manual

The Touring Items Type S Jump Starter is a portable power bank and emergency jump starter designed for vehicles. It features a high-capacity lithium-ion battery, multiple USB output ports (including USB-C PD), a built-in LED flashlight with SOS mode, integrated jumper cables with spark-proof technology, reverse polarity protection, over-current protection, and short-circuit protection. It can jump-start gasoline engines up to 7.0L and diesel engines up to 5.5L. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. First-Time Setup & Charging 4. Specifications 5. Controls and Indicators 6. Jump-Starting a Vehicle 7. Using as a Power Bank 8. Flashlight & Emergency Features 9. Care & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main unit with LCD display, Integrated jumper cables with clamps, USB-A output port, USB-C input/output port, LED flashlight, Power button, Battery level indicator.

FeatureDescription
High-Capacity BatteryLithium-ion battery for multiple jump-starts or device charging
Smart Jumper ClampsSpark-proof technology with reverse polarity protection
LCD DisplayShows battery level, input/output status, and error codes
USB-A Output5V/2.4A for charging phones, tablets, etc.
USB-C PD PortPower Delivery for fast charging (input & output)
LED FlashlightThree modes: steady, strobe, SOS
Power ButtonTurns unit on/off and cycles flashlight modes
Over-Current ProtectionPrevents damage from excessive current draw
Short-Circuit ProtectionShuts down output if short circuit is detected
12V Vehicle AdapterOptional accessory for charging via car cigarette lighter

Safety Information

Read all instructions before use. Keep away from children.

  1. Use only for 12V lead-acid batteries. Do not use for 24V systems.
  2. Ensure jump starter and vehicle are off before connecting clamps.
  3. Connect clamps in correct order: positive (red) to positive (+), negative (black) to negative (-) or unpainted metal ground.
  4. Do not touch clamps together when unit is on.
  5. Store in a cool, dry place away from direct sunlight and liquids.

WARNING! Risk of explosion or fire. Do not use if unit is damaged, swollen, or leaking. Do not disassemble.

First-Time Setup & Charging

Fully charge the jump starter before first use.

  1. Charge via USB-C: Use the provided cable and a USB-C PD charger (not included). LCD will show charging progress.
  2. Charge via 12V car adapter (optional): Plug into vehicle's cigarette lighter port.
  3. Full charge time: Approximately 4-5 hours with a PD charger.
  4. Check battery level: Press POWER button; LCD displays remaining charge (%).

CAUTION! Use only approved chargers. Do not leave charging unattended for extended periods.

Specifications

Controls and Indicators

Access functions via buttons and LCD display. Front Panel: POWER button, LCD screen, USB ports, flashlight LED.

LCD Icons: Battery level (%), USB in/out symbols, error codes (E1-E5).

Flashlight: Press POWER quickly to turn on; press again to cycle modes (steady → strobe → SOS → off). Jump-Start Mode: Press and hold POWER for 3 seconds to activate; LCD shows "READY". Power Bank Mode: Connect device to USB port; unit automatically powers on and begins charging.

Jump-Starting a Vehicle

Follow these steps carefully.

  1. Ensure jump starter is off and vehicle ignition is off.
  2. Connect red clamp to positive (+) terminal of car battery.
  3. Connect black clamp to negative (-) terminal or unpainted metal ground away from battery.
  4. Turn on jump starter by pressing and holding POWER for 3 seconds. LCD shows "READY".
  5. Start the vehicle. Do not crank for more than 3 seconds; wait 30 seconds between attempts.
  6. Once vehicle starts, turn off jump starter.
  7. Remove clamps in reverse order: black first, then red.
  8. Recharge jump starter as soon as possible.

Tip: If vehicle does not start after 3 attempts, check battery or alternator issues.

Using as a Power Bank

Charge smartphones, tablets, GPS devices, etc.

  1. Connect your device to USB-A or USB-C port using appropriate cable.
  2. Unit automatically turns on and begins charging. LCD shows output icon.
  3. To stop charging, disconnect the device.
  4. Note: Using power bank mode reduces jump-start capacity. Recharge regularly.

WARNING! Do not charge the jump starter and use it as a power bank simultaneously.

Flashlight & Emergency Features

Flashlight: Press POWER quickly to activate. Cycle modes by pressing again. SOS mode flashes Morse code distress signal. Emergency: Use strobe mode for visibility. The unit can also charge a phone while flashlight is on (reduces battery life faster).

Care & Storage

Keep clean and dry. Wipe with dry cloth; do not use liquids. Store with 50% charge if not used for extended periods. Recharge every 3 months to maintain battery health.

CAUTION! Do not expose to extreme heat or cold. Do not puncture or modify.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE, RoHS compliant. Copyright © 2025 Touring Items; trademarks of Touring Items Co., Ltd. For support, visit www.touringitems.com or contact 1-800-555-0123.

Troubleshooting

SymptomPossible CauseCorrective Action
Unit does not turn onBattery depletedRecharge fully via USB-C.
LCD shows "E1"Reverse polarity detectedCheck clamp connections; reconnect correctly.
LCD shows "E2"Over-current protection activatedDisconnect devices; wait 30 seconds to reset.
Vehicle does not jump-startClamps not secure / low chargeEnsure solid connection; recharge jump starter.
USB device not chargingFaulty cable / portTry different cable; ensure device is compatible.
Flashlight not workingUnit off / battery deadTurn unit on; recharge if needed.

Reset: Disconnect all devices; press and hold POWER for 10 seconds to reset.

Service: 1-800-555-0123; www.touringitems.com/support

Touring Items Type S Jump Starter Manual © - All Rights Reserved 2025