Types Jump Starter Manual

The Types Jump Starter is a portable power bank and emergency car battery booster designed for jump-starting vehicles (cars, motorcycles, boats) up to 8.0L gasoline or 6.0L diesel engines. It features a high-capacity lithium-ion battery, built-in safety protections (reverse polarity, over-current, short-circuit), USB outputs for charging devices, an LED flashlight with SOS mode, and a digital display showing battery status. Below are key sections for safety, features, operation, charging, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Instructions 3. First-Time Setup 4. Specifications 5. Controls and Indicators 6. Jump-Starting Procedure 7. Charging Devices 8. Maintenance & Storage 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Jump Starter Unit, Smart Clamps (red/black), USB Charging Cable, Wall Charger, User Manual.

FeatureDescription
Battery CapacityHigh-density lithium-ion, 20000mAh
Peak Current2000A for gasoline engines up to 8.0L
USB Outputs2x USB ports (5V/2.4A) for charging phones/tablets
LED FlashlightBright LED with steady, strobe, and SOS modes
Digital DisplayShows remaining battery percentage
Safety ProtectionsReverse polarity, over-current, short-circuit, over-voltage
Input PortMicro-USB for recharging the jump starter
Clamp CablesInsulated, spark-proof with built-in protection circuit
WeightApproximately 1.5 lbs (0.68 kg)
Operating Temp-4°F to 140°F (-20°C to 60°C)

Safety Instructions

Read all instructions before use. Keep away from children.

  1. Connect clamps correctly: Red to positive (+), black to negative (-) or grounded metal.
  2. Do not touch clamps together when unit is on.
  3. Ensure vehicle ignition is OFF before connecting.
  4. Do not use on damaged batteries or vehicles with electrical system issues.
  5. Recharge fully after each use or every 3 months if stored.

WARNING! Risk of explosion or fire if misused. Do not disassemble or expose to water.

First-Time Setup

Charge the jump starter fully before first use.

  1. Connect the wall charger to the unit's Micro-USB input port.
  2. Plug into a standard 120V AC outlet. The digital display will show charging progress.
  3. Charge until display shows 100% (approx. 4-6 hours).
  4. Test the flashlight and USB outputs to ensure functionality.

CAUTION! Use only the provided charger. Do not leave charging unattended for extended periods.

Specifications

Controls and Indicators

Front Panel: POWER Button, MODE Button (flashlight), Digital Display, USB Ports, Micro-USB Input.

Digital Display: Shows battery percentage (0-100%). Flashing warning for low battery or fault.

LED Indicators: Green = sufficient charge for jump start. Red = low battery, recharge required.

Flashlight Operation: Press POWER once to turn on flashlight. Press MODE to cycle through High, Low, Strobe, SOS. Press and hold POWER for 2 seconds to turn off.

Jump Start Ready: Ensure display shows >50% charge. Connect clamps only when ready to start vehicle.

Jump-Starting Procedure

Follow steps in order. Ensure jump starter is OFF before connecting.

  1. Turn off the vehicle's ignition and all electrical accessories (lights, radio).
  2. Connect red clamp to positive (+) terminal of the dead battery.
  3. Connect black clamp to a clean, unpainted metal part of the engine block or chassis (ground).
  4. Turn ON the jump starter (press POWER button twice quickly). The display will light up.
  5. Start the vehicle. It should start within 3-5 seconds. If not, wait 30 seconds before retrying.
  6. Once vehicle is running, turn OFF the jump starter.
  7. Remove clamps in reverse order: black clamp first, then red clamp.
  8. Recharge the jump starter as soon as possible.

Tip: If the clamps are connected incorrectly, the unit will beep and flash a warning. Disconnect immediately and correct the connections.

Charging Devices

Use as a portable power bank for smartphones, tablets, etc.

  1. Connect your device to one of the USB ports using your own USB cable.
  2. The device will begin charging automatically. The display will show remaining battery.
  3. When finished, disconnect your device.
  4. Recharge the jump starter when battery falls below 20%.

Note: Do not charge the jump starter (via Micro-USB) while using it to jump-start a vehicle or charge other devices.

Maintenance & Storage

Store in a cool, dry place away from direct sunlight and moisture.

  1. Recharge fully every 3 months if not in use to maintain battery health.
  2. Clean clamps and casing with a dry cloth. Do not use liquids.
  3. Inspect cables regularly for cracks or damage. Do not use if damaged.
  4. Keep away from metal objects to prevent short circuits.

CAUTION! Do not store in temperatures below -4°F or above 140°F. Do not puncture or crush.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. Contains lithium-ion battery; follow local regulations for disposal/recycling. Copyright © 2025 Types; trademarks of Types Electronics, Inc. For support, visit www.typesproducts.com or contact 1-800-555-0123.

Troubleshooting

SymptomPossible CauseCorrective Action
Jump starter won't turn onBattery depletedRecharge fully via Micro-USB input.
Vehicle does not startInsufficient charge, poor connectionRecharge jump starter; ensure clamps have solid metal contact.
Unit beeps continuouslyReverse polarity, short circuitDisconnect clamps immediately and check connections.
USB ports not charging devicesLow battery, faulty cableRecharge unit; try a different USB cable.
Display shows error codeOver-temperature, internal faultAllow unit to cool; if persists, contact support.
Flashlight not workingBattery dead, button faultRecharge; press MODE button firmly.

Reset: If unit behaves erratically, fully discharge then recharge it.

Service: 1-800-555-0123; www.typesproducts.com

Types Jump Starter Manual © - All Rights Reserved 2025