Vector 700 Amp Jump Starter Manual

The Vector 700 Amp Jump Starter is a portable power source designed for emergency vehicle starting, featuring 700 peak amps, 12V DC output, built-in safety protection circuits, reverse polarity alarm, LED power indicator, heavy-duty clamps, USB charging port, and an integrated LED work light. Powered by a sealed lead-acid battery with AC wall charger. Below are key sections for safety, features, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Heavy-duty clamps, LED power indicator, USB charging port, LED work light, AC wall charger, carrying case.

Safety Instructions

Read all instructions before use. Keep away from children.

1. Wear safety glasses and gloves when jump starting.
2. Ensure vehicles are not touching and both ignitions are OFF.
3. Connect positive (+) clamp to dead battery positive terminal first.
4. Connect negative (-) clamp to engine block or grounded metal, NOT to battery negative.
5. Start working vehicle first, then attempt to start disabled vehicle.
6. Disconnect in reverse order after successful start.

WARNING! Risk of explosion! Do not smoke or create sparks near battery. Do not use on frozen batteries. Never connect clamps directly to each other.

First-Time Setup

Before first use, fully charge the unit.

1. Unpack and inspect: Check for damage to unit, clamps, and cables.
2. Initial charge: Plug AC charger into wall outlet, connect to unit's charging port. Charge until indicator shows green (typically 12-24 hours).
3. Test LED light: Press light button to ensure functionality.
4. Store in dry, cool place away from direct sunlight.

CAUTION! Charge only with provided AC adapter. Do not disassemble unit.

Specifications

• Model: Vector 700 Amp Jump Starter
• Peak Amps: 700A
• Battery: 12V, 18Ah sealed lead-acid
• Clamp Cable Length: 40 inches (101.6 cm)
• USB Output: 5V DC, 2.1A max
• LED Work Light: 3W high-intensity
• Charging Time: 12-24 hours to full charge
• Operating Temp: -4°F to 140°F (-20°C to 60°C)
• Storage Temp: 32°F to 77°F (0°C to 25°C)
• Dimensions: 11.8" x 7.5" x 9.4" (30 x 19 x 24 cm)

Controls and Indicators

Front Panel: Power Indicator LED (Green/Red), USB Port, LED Light Button, Charging Port.

Clamps: Red (+) Positive clamp, Black (-) Negative clamp. Each has insulated handle.

Indicator Lights: Green LED = Fully charged (above 80%). Red LED = Needs charging (below 80%). Flashing Red = Reverse polarity detected (audible alarm will sound).

LED Work Light: Press once for On, press again for Off. Useful for emergency lighting or roadside repairs.

Jump Starting Procedure

Follow steps carefully to avoid damage or injury.

1. Position jump starter near vehicle battery but not touching.
2. Turn OFF both vehicle ignitions and all accessories (lights, radio).
3. Connect RED positive (+) clamp to dead battery's positive terminal.
4. Connect BLACK negative (-) clamp to clean, unpainted metal part of engine block or chassis.
5. Check connections are secure and cables are clear of moving parts.
6. Start the working vehicle (if assisting) and let run for 3-5 minutes.
7. Attempt to start the disabled vehicle. Crank for no more than 5 seconds.
8. If vehicle doesn't start, wait 3 minutes before retrying (max 3 attempts).
9. Once started, disconnect in REVERSE order: Black clamp first, then Red clamp.
10. Recharge jump starter as soon as possible after use.

Tip: If reverse polarity alarm sounds, immediately disconnect clamps and check connections.

Using USB & Accessories

USB port can charge phones, tablets, GPS devices, etc.

1. Ensure jump starter has sufficient charge (Green LED indicator).
2. Use standard USB cable (not included) to connect device to USB port.
3. Device should begin charging automatically.
4. Monitor device and disconnect when fully charged.

Note: USB output is 5V/2.1A. Do not exceed 2.1A total draw. Not for use with high-power devices like laptops.

Charging the Unit

Recharge after each use and every 3 months during storage.

1. Plug AC adapter into 120V wall outlet.
2. Connect charger plug to unit's charging port (ensure correct polarity).
3. Charger LED will typically show red while charging, green when complete.
4. Initial charge: 12-24 hours. Maintenance charge: 8-12 hours.
5. Disconnect charger when not in use to prevent overcharging.

WARNING! Charge in well-ventilated area. Do not cover unit while charging. Use only provided charger.

Care & Maintenance

Keep unit clean and dry. Store in carrying case when not in use.

• Wipe exterior with dry, soft cloth. Do not use liquids or solvents.
• Keep clamps clean and free of corrosion. Use wire brush if necessary.
• Store in cool, dry place (32°F to 77°F / 0°C to 25°C ideal).
• Recharge every 3 months if not in use to maintain battery health.
• Check cables and clamps for damage before each use.

CAUTION! Do not expose to water or extreme temperatures. Do not attempt to open or repair sealed battery compartment.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. UL Listed: Meets safety standards for battery chargers. Copyright © Vector Products, Inc. For support, visit www.vectorproducts.com or contact 1-800-456-1234. Dispose of properly according to local regulations for lead-acid batteries.

Troubleshooting

Reset: Disconnect all devices and recharge fully.

Service: 1-800-456-1234; www.vectorproducts.com